6es7 134-4NB01-0AB0 SIEMENS Analog output module

Description

6es7 134-4NB01-0AB0 SIEMENS Analog output module

Product Dimensions：

Product Description

A Siemens Analog Output (AO) module serves as the interface between a programmable logic controller’s digital logic and proportional field actuators. It receives a digital value—calculated by the CPU’s control algorithms—and translates it into a standardized analog current or voltage. This allows the system to command devices to specific positions or speeds. To ensure high accuracy and system safety, these modules feature advanced digital-to-analog conversion (DAC) circuitry, galvanic isolation to prevent ground loops, and built-in diagnostic capabilities to monitor the health of the output loop.

Product Parameters

The performance and compatibility of an analog output module are defined by its electrical precision and signal range:

• Output Signal Ranges: Support for standard industrial formats, typically 0 to 10 V, ±10 V, 0 to 20 mA, or 4 to 20 mA.

• Resolution: The granularity of the output signal, usually ranging from 12-bit to 16-bit, which determines how small the incremental changes can be.

• Accuracy/Error Limits: The maximum deviation from the intended value at room temperature and across the entire operating temperature range.

• Settling Time: The duration required for the output signal to reach and stabilize at a new commanded value after a step change.

• Load Impedance: The maximum resistance (for current outputs) or minimum resistance (for voltage outputs) that the module can successfully drive.

• Diagnostics: Capabilities such as short-circuit detection for voltage outputs and wire-break detection for current loops.

Product Advantages

• High Precision Control: Provides smooth, high-resolution signal generation, which is critical for maintaining stable process variables and fine-tuning mechanical movements.

• Flexible Configuration: Each channel can often be independently configured for different signal types (voltage vs. current) via software, reducing the need for multiple hardware variants.

• Fast Response Times: High-speed conversion cycles ensure that control loops, such as PID regulators, can react quickly to process disturbances.

• Robust Electrical Protection: Integrated isolation protects the internal PLC backplane from external electrical noise and high-voltage transients present in the field.

• User-Friendly Maintenance: Clear diagnostic LEDs and software-reported faults allow for rapid identification of wiring issues or actuator failures without extensive manual testing.

Usage Precautions

• Shielding and Grounding: Analog signals are highly susceptible to electromagnetic interference; always use shielded twisted-pair cables and ensure the shield is grounded at the designated entry point.

• Cable Length and Resistance: Be mindful of the voltage drop over long cable runs for voltage signals, or the total loop resistance for current signals, to ensure the actuator receives the correct value.

• Safe State Behavior: Properly configure the “Substitute Value” in the engineering software so the output goes to a predetermined safe value (e.g., 4mA or 0V) if the CPU stops or communication is lost.

• External Power Supply: Many modules require a dedicated external 24V DC supply for the analog circuits; ensure this power is clean and free of heavy industrial noise.

• Separation of Cables: Route analog output cables in separate conduits or trays away from high-power AC cables and variable frequency drive (VFD) motor leads to prevent signal distortion.

Product Applications

• Modulating Valve Control: Precise positioning of control valves in fluid and gas systems to regulate flow, pressure, or temperature.

• Speed Setpoints: Providing reference signals to variable frequency drives (VFDs) or DC motor controllers to manage the rotational speed of pumps, fans, and conveyors.

• Actuator Positioning: Driving proportional actuators in HVAC systems, such as dampers and louvers, to maintain environmental conditions.

• Power Regulation: Sending control signals to power controllers for industrial heating elements or specialized lighting systems.

• Signal Retransmission: Passing processed variables from the PLC to external systems like stand-alone recorders, display panels, or secondary controllers.

Shipping Port: Xiamen, China

Payment: Bank of Chicago, Bank of Singapore

Express cooperation: fedex, DHL, UPS and your express account

Service: Professional Sales provides 24 hours /7 days online service

Please make an inquiry for more models：