6ES7157-0AG81-0XA0 SIEMENS Analog output module

Description

6ES7157-0AG81-0XA0 SIEMENS Analog output module

Product Dimensions：

Product Description

Siemens Analog Output Modules function as the precision control interface of an automation system. While a digital module only understands “on” or “off,” an analog module can output a wide range of values within a specific scale. These modules receive digital data via the backplane bus and, through internal Digital-to-Analog Converters (DAC), generate corresponding current or voltage signals. They are built to provide high-speed response times and are typically housed in rugged enclosures suitable for industrial environments. Their modular design allows them to be integrated into centralized or distributed configurations depending on the system architecture.

Product Parameters

The technical performance of an analog output module is defined by its ability to maintain signal integrity and accuracy. Key parameters include:

• Signal Ranges: Support for standard industrial signals, typically voltage ($0$ to $10V$, $pm10V$) and current ($0$ to $20mA$, $4$ to $20mA$).

• Resolution: Usually ranging from 12-bit to 16-bit; higher resolution allows for finer increments in the output signal.

• Accuracy/Error Limits: Defined by the operational limit at room temperature and the temperature coefficient over the full operating range.

• Settling Time: The duration required for the output signal to reach a specified value after a change in the digital input.

• Load Impedance: Specifies the maximum resistance for current outputs and the minimum resistance for voltage outputs to ensure signal stability.

• Diagnostic Features: Capability to detect common faults such as short circuits (for voltage) or wire breaks (for current).

Product Advantages

• High Precision Control: Advanced circuitry ensures that the output signal remains stable and accurate even in environments with electrical noise.

• Enhanced Diagnostics: Real-time monitoring allows the system to identify wiring issues or actuator failures immediately, reducing maintenance time.

• Galvanic Isolation: The modules provide electrical separation between the internal electronics and the field level, protecting the PLC from external surges.

• Parameterizable Behavior: Users can configure how the module reacts to a CPU stop—for example, holding the last value or switching to a predefined substitute value for safety.

• Ease of Engineering: Full integration with the TIA Portal allows for easy scaling of units (e.g., converting $0-100%$ in software directly to $4-20mA$ hardware output).

Precautions for Use

• Shielding and Grounding: Analog signals are highly susceptible to electromagnetic interference; therefore, shielded cables must be used and grounded correctly at the specified points.

• Load Matching: It is critical to ensure that the impedance of the connected actuator (e.g., a valve positioner) falls within the module’s allowable range to prevent signal clipping or hardware damage.

• Signal Interference: Low-voltage analog cables should be routed separately from high-voltage power cables to avoid inductive coupling and signal fluctuations.

• Common Mode Voltage: Ensure that the potential difference between the ground of the module and the ground of the field device does not exceed the maximum allowable common-mode voltage.

• Calibration Requirements: While factory-calibrated, critical applications should involve periodic verification of the output accuracy to account for component aging or environmental drift.

Product Applications

Siemens Analog Output Modules are essential in any scenario requiring graduated or proportional control:

• Variable Speed Drives: Providing the speed setpoint to frequency converters to manage motor rotation in conveyors or fans.

• Proportional Valve Control: Modulating the opening degree of hydraulic or pneumatic valves to control fluid flow or pressure.

• Heating Control: Sending signals to power controllers (such as SCRs) to regulate the intensity of industrial heating elements.

• Actuator Positioning: Controlling the precise movement of dampers, louvers, or robotic arms in complex mechanical systems.

• Signal Retransmission: Passing processed process values to external hardware such as chart recorders or secondary monitoring displays.

Shipping Port: Xiamen, China

Payment: Bank of Chicago, Bank of Singapore

Express cooperation: fedex, DHL, UPS and your express account

Service: Professional Sales provides 24 hours /7 days online service

Please make an inquiry for more models：